Manuals:BXFbl:Radio Setup:RemoteSat/en: Difference between revisions
Jump to navigation
Jump to search
Updating to match new version of source page Tags: Mobile edit Mobile web edit |
Updating to match new version of source page |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{TOC_BXFbl|Manuals:BXFbl:Radio_Setup:FRSKY/en|Manuals:BXFbl:Radio_Setup:Standard_PPM/en||}} | {{TOC_BXFbl|Manuals:BXFbl:Radio_Setup:FRSKY/en|Manuals:BXFbl:Radio_Setup:Standard_PPM/en|RADIOSETUP|}} | ||
{{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite|noerror}} | {{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite|noerror}} | ||
__TOC__ | __TOC__ | ||
| Line 46: | Line 46: | ||
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port. | * Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port. | ||
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system). | * To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system). | ||
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed. | * After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed. | ||
<br /> | <br /> | ||
| Line 58: | Line 51: | ||
<gallery mode="nolines"> | <gallery mode="nolines"> | ||
File:DSMXbind MB | File:DSMXbind MB Plus 1.jpg|You need: RX, bind plug and battery | ||
File:DSMXbind MB | File:DSMXbind MB Plus 2.jpg|Connect bind plug at [SYS] and RX at [DI2] | ||
File:DSMXbind MB | File:DSMXbind MB Plus 3.jpg|Power up MICROBEAST: LEDs flash | ||
File:DSMXbind MB | File:DSMXbind MB Plus 4.jpg|Start bind sequence on radio | ||
File:DSMXbind MB Plus 5.jpg|Bind successful | |||
File:DSMXbind MB | File:DSMXbind MB Plus 6.jpg|Proceed with setup | ||
File:DSMXbind MB | |||
</gallery> | </gallery> | ||
<br /> | |||
'''MICROBEAST ULTRA (v5.9.x)'''<br /> | |||
* Disconnect(!) the Spektrum® remote satellite and switch on the power supply. | |||
* During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release | |||
* LEDs A and H flash in alternating sequence | |||
* Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST | |||
* Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system). | |||
* After successful binding procedure the receiver‘s LED will stay solid | |||
* Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed. | |||
<br /> | |||
<br /> | <br /> | ||
| Line 76: | Line 79: | ||
=BEASTX setup= | =BEASTX setup= | ||
In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | ||
for your radio system if needed.<br /> | for your radio system if needed. By default the BEASTX system has a preset channel order that fits to most SPEKTRUM® and JR® radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | ||
<br /> | <br /> | ||
{| class="wikitable" style="text-align: center; margin-left: 70px; background-color: #F9DDCC; border: solid #F18308 2px;" | {| class="wikitable" style="text-align: center; margin-left: 70px; background-color: #F9DDCC; border: solid #F18308 2px;" | ||
|+ style="caption-side:bottom;|SPEKTRUM® default channel order | |+ style="caption-side:bottom;|SPEKTRUM® / JR® default channel order | ||
|- | |- | ||
! style="width: 100px; background-color: #f4bf9e" | Channel | ! style="width: 100px; background-color: #f4bf9e" | Channel | ||