Manuals:BXFbl:Radio Setup:RemoteSat: Difference between revisions
Jump to navigation
Jump to search
Shornstein (talk | contribs) No edit summary |
Shornstein (talk | contribs) Marked this version for translation |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
<translate> | <translate> | ||
<!--T:1--> | <!--T:1--> | ||
{{TOC_BXFbl|Manuals:BXFbl:Radio_Setup:FRSKY/en|Manuals:BXFbl:Radio_Setup:Standard_PPM/en||}} | {{TOC_BXFbl|Manuals:BXFbl:Radio_Setup:FRSKY/en|Manuals:BXFbl:Radio_Setup:Standard_PPM/en|RADIOSETUP|}} | ||
{{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite|noerror}} | {{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite|noerror}} | ||
__TOC__ | __TOC__ | ||
| Line 16: | Line 16: | ||
<br /> | <br /> | ||
<!--T:3--> | |||
= Connection scheme = | |||
<br /> | <br /> | ||
'''MICROBEAST PLUS / MICROBEAST ULTRA'''<br /> | '''MICROBEAST PLUS / MICROBEAST ULTRA'''<br /> | ||
| Line 45: | Line 46: | ||
<br /> | <br /> | ||
<!--T:23--> | |||
=Bind procedure Spektrum® DSMX satellite= | |||
<br /> | <br /> | ||
{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}} | {{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}} | ||
| Line 88: | Line 90: | ||
<br /> | <br /> | ||
<!--T:13--> | |||
=BEASTX setup= | |||
In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | ||
for your radio system if needed. By default the BEASTX system has a preset channel order that fits to most SPEKTRUM® and JR® radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | for your radio system if needed. By default the BEASTX system has a preset channel order that fits to most SPEKTRUM® and JR® radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | ||
| Line 122: | Line 125: | ||
<br /> | <br /> | ||
<!--T:15--> | |||
==MICROBEAST PLUS / MICROBEAST ULTRA== | |||
Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. <br /> | Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. <br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:16--> | |||
==NANOBEAST== | |||
Make sure throttle on the radio is in idle position. Connect the remote receiver to ''SAT'' port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU. | Make sure throttle on the radio is in idle position. Connect the remote receiver to ''SAT'' port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU. | ||
<br /> | <br /> | ||
| Line 133: | Line 138: | ||
<br /> | <br /> | ||
<!--T:17--> | |||
==Setup with StudioX== | |||
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the Control menu in StudioX and click the SCAN button in this menu's screen.<br /> | You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the Control menu in StudioX and click the SCAN button in this menu's screen.<br /> | ||
<br /> | <br /> | ||