Manuals:BXFbl:Parameters/en

There are a lot of different parameters to optimize the system and tweak it to your personal preference. Here is an overview and a short description of the parameters. Some parameters can be directly changed from the device's menu. More complex parameters can be adjusted using the StudioX app. You will get more details about the parameters in the following sections.

On MICROBEAST PLUS / ULTRA the current menu step is indicated by the LED letters. In PARAMETER MENU the menu LED must be flashing.

With NANOBEAST the current menu step is indicated by number of flashes of the Status LED. In PARAMETER MENU the Status LED will flash in purple color. Steps A to G are indicated by 1 to 7 flashes. From steps H to M onwards again there will be 1 to 7 flashes to indicate the current menu step. But here the first flash will be long.

PARAMETER MENU overview

Menu	Description	off	purple	red flashing	red	blue flashing	blue
A	Quick Trim
B	Control Style	custom	normal	sport	pro	extreme	linear
C	Speed flight stability	custom	very low	low	medium	high	very high
D	Rudder rate consistency	custom	very low	low	medium	high	very high
E	Stick deadzone	custom	very small	small	medium	large	very large
F	Revo Mix	custom	off	low - left	low - left	low - right	high - right
G	Cyclic response	custom	normal	more reactive	very reactive	aggressive	very aggressive
H	Pitch boost	custom	off	low	medium	high	very high

Governor parameters (only when Governor feature is installed)

Menu	Description	off	purple	red flashing	red	blue flashing	blue
I	Throttle response	soft	normal	quick	hard	aggressive	very aggressive
J	Slow rampup speed	custom	50	100	200	300	400
K	Fast rampup speed	custom	slow rampup	300	500	700	900

AttitudeControl parameters (only when Rescue feature is installed)

Menu	Description	off	purple	red flashing	red	blue flashing	blue
L	Operation mode	disabled	Angular Mode	Bail out rescue	Bail out w. Pitch	3D - Mode	3D w. Pitch
M	Rescue pitch	> 20% of max	> 30% of max		> 50% of max		> 70% of max

A - Quick Trim

Tap or hold sticks for pitch/elevator and roll/aileron to trim swashplate in desired cyclic direction. Use rudder stick to trim the collective. When using RESCUE function (only RESCUE or PROEDITION firmware) enable the rescue function on the radio to enable trim fucntion for artifical horizon. Here you can trim the pitch or roll axis by tapping/holding the corresponding stick on the radio.

B - Control Style

Tap rudder stick to select Control Style (change LED color). The higher the value, the more responsive your helicopter will be and the higher is the maximum rotation rate. Use setting "linear" if you like to use expo and rate function on the radio.

C - Speed flight stability

Tap rudder stick to select Speed flight stability (change LED color). The higher the value, the more locked in your helicopter will be in fast forward flight. It's best to try finding the lowest suitable setting.

D - Rudder rate consistency

Tap rudder stick to select Rudder rate consistency (change LED color). It determines how hard the tail gyro tries to maintain a given rotation rate. If the value is set too low, pirouettes will be inconsistent during fast forward flight and the helicopter will slowly drift on the vertical axis in stationary hovering flight with crosswinds. It's best to try finding the lowest suitable setting.

E - Stick dead zone

Tap rudder stick to select Stick dead zone (change LED color). It defines the range around the very center of the stick in which the system will not react to stick inputs. It's best to try finding the lowest suitable setting.

F - Revo Mix

Tap rudder stick to select amount of Revo Mixing (torque precompensation) and direction (change LED color). Use Revo Mix when the tail goes away in torque direction when applying a sudden collective or cyclic input.

G - Cyclic response

Tap rudder stick to select amount of Cyclic response (change LED color). This determines how aggressive the system will responds to cyclic control commands (roll and pitch). Use the normal setting for linear reaction or gradually increase for a more reactive feeling.

H - Pitch boost

Tap rudder stick to select amount of Pitch boost (change LED color). This function will transfer quick thrust stick movements into an overshooting pitch movement. This can be especially useful in 3D aerobatics when very rapid collective pitch changes are necessary for certain flight maneuvers. With pitch boost you don't need to move the stick over full range of movement. Small movements are sufficient when moving the stick quick enough.