Manuals:BXFbl:Radio Setup:SRXL: Difference between revisions
Jump to navigation
Jump to search
Shornstein (talk | contribs) No edit summary |
Shornstein (talk | contribs) Marked this version for translation |
||
| Line 11: | Line 11: | ||
<br /> | <br /> | ||
<!--T:3--> | |||
= Connection scheme = | |||
<br /> | <br /> | ||
[[File:srxl.png|300px|right]] | [[File:srxl.png|300px|right]] | ||
| Line 76: | Line 77: | ||
<br /> | <br /> | ||
<!--T:12--> | |||
=Radio setup= | |||
Make sure that the output of your receiver is set to SRXL, X-Bus (B), UDI, SUMD, or whatever it is called.<br /> | Make sure that the output of your receiver is set to SRXL, X-Bus (B), UDI, SUMD, or whatever it is called.<br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:13--> | |||
=BEASTX setup= | |||
In order to use your SRXL receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | In order to use your SRXL receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | ||
for your radio system.<br /> | for your radio system.<br /> | ||
<br /> | <br /> | ||
<!--T:14--> | |||
==MICROBEAST PLUS / MICROBEAST ULTRA== | |||
Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If using a Graupner HOTT receiver with SUMD output, you can enable the additional telemetry communication on SYS port at Menu LEDs L & M; push the button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. <br /> | Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If using a Graupner HOTT receiver with SUMD output, you can enable the additional telemetry communication on SYS port at Menu LEDs L & M; push the button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. <br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:15--> | |||
==NANOBEAST== | |||
Connect the SRXL port of the receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If using a Graupner HOTT receiver with SUMD output, you can enable the additional telemetry communication on SYS port at Menu LEDs L & M (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push the button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | Connect the SRXL port of the receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If using a Graupner HOTT receiver with SUMD output, you can enable the additional telemetry communication on SYS port at Menu LEDs L & M (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push the button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:16--> | |||
==Setup with StudioX== | |||
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen.<br /> | You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen.<br /> | ||
<br /> | <br /> | ||