Manuals:BXFbl:Radio Setup:Jeti EXBUS: Difference between revisions
Jump to navigation
Jump to search
Shornstein (talk | contribs) No edit summary |
Shornstein (talk | contribs) Marked this version for translation |
||
| Line 11: | Line 11: | ||
<br /> | <br /> | ||
<!--T:3--> | |||
= Connection scheme = | |||
<br /> | <br /> | ||
{| class="wikitable" style="width:30%; text-align: center; margin-left: 50px; background-color: #F9DDCC; border: solid #F18308 2px;" | {| class="wikitable" style="width:30%; text-align: center; margin-left: 50px; background-color: #F9DDCC; border: solid #F18308 2px;" | ||
| Line 82: | Line 83: | ||
<br /> | <br /> | ||
<!--T:16--> | |||
=Radio setup= | |||
Enable EXBUS | Enable EXBUS | ||
Telemetry....<br /> | Telemetry....<br /> | ||
| Line 88: | Line 90: | ||
<br /> | <br /> | ||
<!--T:17--> | |||
=BEASTX setup= | |||
In order to use your EXBUS receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | In order to use your EXBUS receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | ||
for your radio system. By default the BEASTX system has a preset channel order that fits to most JETI radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | for your radio system. By default the BEASTX system has a preset channel order that fits to most JETI radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | ||
| Line 122: | Line 125: | ||
<br /> | <br /> | ||
<!--T:19--> | |||
==MICROBEAST PLUS / MICROBEAST ULTRA== | |||
Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. <br /> | Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. <br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:20--> | |||
==NANOBEAST== | |||
When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | ||
<br /> | <br /> | ||
| Line 138: | Line 143: | ||
<br /> | <br /> | ||
<!--T:22--> | |||
==Setup with StudioX== | |||
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when the EXBUS receiver is connected to SYS port on MICROBEAST PLUS / ULTRA, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port using the optional adapter from standard servo connector to 5-pin JST. For further informations please refer to the StudioX instruction notes.<br /> | You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when the EXBUS receiver is connected to SYS port on MICROBEAST PLUS / ULTRA, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port using the optional adapter from standard servo connector to 5-pin JST. For further informations please refer to the StudioX instruction notes.<br /> | ||
<br /> | <br /> | ||