Manuals:BXFbl:Radio Setup:Futaba SBUS: Difference between revisions
Jump to navigation
Jump to search
Shornstein (talk | contribs) No edit summary |
Shornstein (talk | contribs) Marked this version for translation |
||
| Line 15: | Line 15: | ||
<br /> | <br /> | ||
<!--T:4--> | |||
= Connection scheme = | |||
<br /> | <br /> | ||
{| class="wikitable" style="width:30%; text-align: center; margin-left: 50px; background-color: #F9DDCC; border: solid #F18308 2px;" | {| class="wikitable" style="width:30%; text-align: center; margin-left: 50px; background-color: #F9DDCC; border: solid #F18308 2px;" | ||
| Line 35: | Line 36: | ||
<br /> | <br /> | ||
==SBUS / SBUS2 - control only== | <!--T:5--> | ||
==SBUS / SBUS2 - control only== | |||
Using SBUS/SBUS2 to control your helicopter is possible with any of the BEASTX devices. Connect the SBUS/SBUS2 port of your receiver with the DI1 port of your BEASTX system using one of the provided standard servo wires.<br /> | Using SBUS/SBUS2 to control your helicopter is possible with any of the BEASTX devices. Connect the SBUS/SBUS2 port of your receiver with the DI1 port of your BEASTX system using one of the provided standard servo wires.<br /> | ||
<br /> | <br /> | ||
| Line 56: | Line 58: | ||
<br /> | <br /> | ||
<!--T:9--> | |||
==SBUS2 - control and telemetry== | |||
For bi-directional telemetry connect your SBUS2 signal wire either to the SYS port or to the DI2 port of your MICROBEAST ULTRA. In both cases it is mandatory to add a pull-down 4,7kOhm resistor between signal line and ground (minus). When using the DI2 port, also you need an adapter from standard servo connector to 5-pin JST as shown below. | For bi-directional telemetry connect your SBUS2 signal wire either to the SYS port or to the DI2 port of your MICROBEAST ULTRA. In both cases it is mandatory to add a pull-down 4,7kOhm resistor between signal line and ground (minus). When using the DI2 port, also you need an adapter from standard servo connector to 5-pin JST as shown below. | ||
| Line 74: | Line 77: | ||
<br /> | <br /> | ||
<!--T:13--> | |||
=Radio setup= | |||
Telemetry....<br /> | Telemetry....<br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:14--> | |||
=BEASTX setup= | |||
In order to use your SBUS / SBUS2 receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | In order to use your SBUS / SBUS2 receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering | ||
for your radio system. By default the BEASTX system has a preset channel order that fits to most FUTABA radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | for your radio system. By default the BEASTX system has a preset channel order that fits to most FUTABA radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br /> | ||
| Line 113: | Line 118: | ||
<br /> | <br /> | ||
<!--T:16--> | |||
==MICROBEAST PLUS / MICROBEAST ULTRA== | |||
Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. | Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. | ||
For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | ||
| Line 119: | Line 125: | ||
<br /> | <br /> | ||
<!--T:17--> | |||
==NANOBEAST== | |||
Power up NANOBEAST. Then connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | Power up NANOBEAST. Then connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br /> | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
<!--T:18--> | |||
==Setup with StudioX== | |||
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes. Please note that when the SBUS2 receiver is connected to SYS port on MICROBEAST ULTRA, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port using the optional adapter from standard servo connector to 5-pin JST.<br /> | You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes. Please note that when the SBUS2 receiver is connected to SYS port on MICROBEAST ULTRA, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port using the optional adapter from standard servo connector to 5-pin JST.<br /> | ||
<br /> | <br /> | ||