CRSF and ELRS

From BEASTX Wiki
Revision as of 10:27, 3 June 2024 by FuzzyBot (talk | contribs) (Updating to match new version of source page)
Jump to navigation Jump to search


The BEASTX devices supports the CRSF serial protocol that was invented by Team Blacksheep (TBS) for their Crossfire radios modules. This protocol is also available for many OPENTX/EDGETX radio systems, especially with ExpressLRS (ELRS). It gets widely used now, not only for drones but also helicopters and wings. The protocol allows very high transmission rates and is very convenient to use.

If you like, here you can download the BEASTX background template for your EDGETX radio:




Connection scheme


You can use CRSF only for sending control data to you BEASTX device. In this case only connect the TX line of the receiver to the DI1/IO1 port of your BEASTX device.

To enable the telemetry backlink to the radio, connect the RX line of the receiver to the SYS port of your BX device. When the SYS port is already occupied by an SRXL2 device (Spektrum AVIAN ESC) you can alternatively connect the RX line to the DI2 pin (MICROBEAST PLUS / ULTRA only).

In order to use SYS for connecting the BLE2SYS / USBSYS for using the StudioX app, simply disconnect the receiver from SYS temporarily, switch off your radio and power cycle your device. It will then enable "normal" SYS operation for programming purpose.

CRSF/ELRS connection options
DI1 / IO1 SYS SAT DI2
TX line - - -
TX line RX line ESC telemetry -
TX line SPEKTRUM SRXL2 ESC - RX line



MICROBEAST PLUS
The ESC or throttle servo is connected at CH5 port. If needed the telemetry data line from the ESC is connected to the SAT port at the 5-pin JST port at side of the device using an adapter.


MICROBEAST ULTRA
The ESC or throttle servo is connected at IO2 port. If needed the telemetry data line from the ESC is connected to the SAT port at the 5-pin JST port at side of the device using an adapter.


NANOBEAST
The ESC or throttle servo is connected at CH1 port. If needed the telemetry data line from the ESC is connected to the SAT port.


Radio setup

When using a ELRS receiver make sure to enable the CRSF using the web interface of your receiver. Using the RADIOMASTER ER-series receiver you can change the output signals of the receivers as needed. To access the web interface, power up the receiver, wait for one minute until the receiver flashes quickly, then connect your computer or smartphone to the new wifi network 10.0.0.1 (Password: expresslrs).

For the ELRS settings in the radio we recommend using the D500 Wide mode or 333Hz Full mode. Note that only in "FullRes" mode all channels have full resolution. When using channels 6 and above only for controling the ESC, gyro and similar control functions, the "Wide mode" should be OK as well. (Please note that CH5 is not available as this is used as binary switch channel!). We mostly use D500 mode which is working very well. The BX devices can even use the 1000Hz mode but we do not recommend this mode due to restricted radio range and lack of safety options. Also this will not give any benefit when driving servos at a much slower rate.


BEASTX setup

In order to use your CRSF/ELRS receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering for your radio system.

JETI default channel order
Channel Function
CH1 Thrust / Collective
CH2 Roll / Aileron
CH3 Pitch / Elevator
CH4 Rudder
CH5 - (Don't use!)
CH6 Throttle
CH7 Gain
CH8 AttitudeControl (optional)
CH9 Governor (optional)
CH10 Aux channel (optional)

(The optional functions are described in the section Optional features.)


MICROBEAST PLUS / MICROBEAST ULTRA

Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section.


NANOBEAST

Connect the TX line of the receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.


Setup with StudioX

You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the Control menu in StudioX and click the SCAN button in this menu's screen. Please note that when the RX line of the receiver is connected to SYS port, you must disconnect the receiver from SYS temporarily, switch off your radio and power cycle your device. It will then enable "normal" SYS operation for programming purpose. For further informations please refer to the StudioX instruction notes.

(Picture sys adapter!)